Airspray FPro manual gun easy solution

• Large choice of projectors for flow adjustments and different spray shapes
• High transfer efficiency up to 78%

• All inclusive mobile mobile version allows you to hang the hoses and gun on the cart for maximum mobility
• Choice of several types of pumps and pressure tanks to meet every specific application need.

• Durable wheels
• Maintenance is optimized by the number of spare parts with easy disassembling

The FPro P Airspray spraygun must be fitted with our genuine spray nozzles to guarantee the best results.

You must choose the right nozzle taking into account the required thickness and fan width pattern (example 0.9 nozzle used to get a flowrate of 240 cc). To help you choose your spray nozzle, please refer to the configurator. You need to adapt your aircap according to the viscosity of the paint and the fan width.( Example, use an HVLP aircap for stains at 16s CA4 viscosity)

"Tips and Tricks":

We recommend at the end of the day you leave the aircap in the solvent until the next use.

Two models of FPro P spray guns are available:  - LP mention engraved on the body used for HVLP and LVLP spraying aircaps of the gun - and Conv mention engraved on the body used for conventional spraying

"Tips and Tricks": When you flush, we recommend you place your gun on the side wall of the paint container to prevent any splashing due to the vortex effet or you can use our Autowash gun flush box.

You will need to select the right length of hoses between the paint pump and the spray gun depending on your installation and your spray booth location. You also will need to select the right diameter to avoid too much pressure loss. (pressure loss will directly impact the fluid section size of the pump needed). As an example, with a water-based paint with a viscosity of 100 cps, a 7.5 meters hose, diameter 6.35, will generate a 0.5 bar pressure loss.

"Tips and Tricks": For moisture sensitive paints, you will need to choose PTFE hoses.

PMP150 is our easiest pumping solution. It is a diaphragm pump (for application requiring a 1:1 ratio) and can be used with adhesive, medium viscosity or harsh coating.

"Tips and Tricks": You need to operate this pump with a clean air - without any condensation -  it is why we recommend the use of an epurator on the air circuit.

During the flushing operation, always open wide the fluid regulator for a better cleaning of the fluid passage recessed areas. The suction rod need also to remain in the solvent.

This cup lub pump range represents an economical production/price ratio. Those pumps are dedicated for solvant and water-based paints.

Our SAMES KREMLIN pump range features fluid section stainless steel This pump is not recommended for moisture-sensitive materials. In case of multiple color changes, we recommend to use the smallest hydraulic section which matches your need to save paint and solvents..

"Tips and Tricks": In case of very viscous materials, this pump type can be fed under pressure.

You should select the size of your pressure pot according to your application and paint. Example, for touch-up works, we recommend you use the 2 liters capacity tank. For water-based paints, we recommend to use a stainless steel tank fitted with an agitator and a bottom outlet.

"Tips and Tricks": For large capacity pressure pots, you can fit several propellers on the agitator rod.

The main filtration can be done at the paint pump using a dedicated filter mounted at the product output of the paint pump. The filter screen need to be adjusted depending on your paint to prevent tip blockage when spraying.

We supply two different types of filters:

• the inline filter which requires a very small amount of solvent for flushing sequences
• the filter accumulator which is the one which is usually mounted on our pumps.

"Tips and Tricks": Place the filter with the vessel oriented on the top to be used as an accumulator

Allows you to pump the material directly from a drum container. Different suction hose diameters are available regarding the viscosity of the paint. We supply suction rods for drums with a capacity of 60 liters and 200 liters.

"Tips and Tricks": Even if the suction rod is not a wear part, we recommend you check it daily as the strainer is not plugged. Always keep a couple extra strainers in stock!

In case of small production runs, we recommend you use our 6 liter hopper to feed the pump.

Tips and Tricks": During the flushing sequence, we recommend you spray with the gun on the inner hopper wall for easier cleaning and to save a maximum amount of solvent.

An agitator will maintain all the components of the paint in constant movement preventing any deposition of pigments and will keep the best performance of the pump and the gun. It will also ensure perfect homogenous colors during the application.

"Tips and Tricks": When manipulating the agitator, we highly recommend you shut down the air in the circuit , even if the ball valve is off.