SAMES KREMLIN | 15C25 Airmix® Paint Pump

Description

Efficiency: perfect for Airmix® finish
Optimization: built with minimal parts
Simplicity: lowest cost of ownership

▶ Technical manual

PERFORMANCE

Constant delivery and pulse free for superior finish
Priming at very low air pressure (0.6 bar)

PRODUCTIVITY

Large foot valve to handle high viscosity materials up to 5,000 cPs
A closed construction to prevent from risk of injuries & to protect lubricant from external contamination
Quick maintenance thanks to an easy rotable outlet fitting
Facilitate pump priming & flushing thanks to a design made to eliminate dead zone: time saved
Leak monitoring vent hole for fast control
A quiet air motor make very low noise

SUSTAINABILITY

45% less part vs competitors for the air motor to provide a better maintenance
Differential air motor to avoid the paint pump from frost
Ultra coated pluger for less friction & improved abrasion resistance
Single GT seal to avoid throat packing maintenance & low friction & offers a large lubricant wet cup

The 15C25 Compact Airmix® paint pump is recommended to handle all types of materials, ranging from medium to low viscosity.

Technical data table

Designation	Value	Unit: metric (US)
Pressure Ratio	15/1
Maximum Fluid Pressure	90 (1305)	bar (psi)
Maximum Air Pressure	6 (87)	bar (psi)
Air Consumption	2.8 (1.65)	m³/h (cfm)
Weight	7.7 (17)	kg (lbs)
Maximum Temperature	60 (140)	°C (°F)
Weighted Sound Level	71.2	dBA
Recommended Air Pressure	2 - 5 (29 - 72.5)	bar (psi)
Fluid Output at 30 cycles/mn	0.75 (0.2)	l/min (gal/mn)
Fluid Output at 20 cycles/mn	0.5 (0.13)	l/mn (gal/mn)
Fluid Volume Per Cycle	25	cc
Free Flow Rate	1.5 (0.39)	l/mn (gal/mn)
Fluid Output at 15 Cycles	0.375 (0.01)	l/mn
Air Consumption at 30 Cycles/mn at 4 Bar (60 psi)	2.8	m³/h (cfm)
Displacement Per Cycle	25 (1.52)	cc (cubic inch)
Motor Type	245-4
Air Inlet	F3/8" BSP / F3/8" BSP
Fluid Outlet	F 3/8 " NPS / M1/2 JIC
Fluid Inlet	F 1/2 " BSP / M26x125
Hard Chrome Stainless Steel, Wetted Parts	♦
Number of cycles per liter of products	40
Sealing packing upper and lower GT polyethylene	♦
Height	57.5 (22.6)	cm (in)
Width	32 (12.6)	cm (in)
Depth	17 (6.69)	cm (in)
Wetted parts stainless steel	♦

Technologies

GT Sealing

This technology represents a new generation of sealing designed to extend the life of a pump piston.

Cup Lub

A pump with a lubricant-filled cup on the top of the fluid section.

2 Ball

2 ball pumping technology is highly utilized in fluid sections with one ball / seat for suction & the other ball / seat for feeding.

Triple Chrome Layer

This is a special treatment for very high sustainability & is applied to the piston of the fluid section of a pump.

Documents

Select all documents

Leaflet Airmix 15C25 30C25 paint pump (english version) sames kremlin

Format : application/pdf
Size : 382Ko

Select the document

catalog-airmix-range-sames-kremlin

Format : application/pdf
Size : 3Mo

Select the document

General Catalog (only for North American market) SAMES KREMLIN

General Catalog North America

Format : application/pdf
Size : 6Mo

Select the document

Materials

Primer Polyurethane Multi-Component

Designed to hide profile & surface imperfections, multi-component polyurethane primers & sealers improve adhesion of top coats to the substrate due to the addition of a hardener.

Primer Water-Based

Designed to hide profile & surface imperfections, water-based primers & sealers are environmentally friendly.

Primer Polyurethane

Designed to hide profile & surface imperfections, polyurethane primers & sealers promote adhesion of top coats to the substrate.

CARC Water-Based

Chemical Agent Resistant Coating (CARC) is available in a water-based solution for environmental protection.

CARC Epoxy Multi-Component

Chemical Agent Resistant Coating (CARC) is a paint commonly applied to military vehicles to provide protection against chemical & biological weapons. The surface of the paint is engineered to be easily decontaminated after exposure to chemical warfare & biological warfare agents. The paint is also resistant to damage & removal by decontaminating solutions.

CARC Polyurethane Multi-Component

Chemical Agent Resistant Coating (CARC) can be two-component polyurethane paint commonly applied to military vehicles to provide protection against chemical & biological weapons.

Top Coat Polyurethane Multi-Component

Polyurethane Top Coat is a two- or three-pack isocyanate-cured polyurethane that gives a durable, high gloss finish. Isocyanates included in the hardener are moisture-sensitive & need a specific process for insulating the circuit.

Penetrant (NDT Testing)

Dye penetrant inspection (DPI), also called liquid penetrant inspection (LPI) or penetrant testing (PT), is a widely applied & low-cost inspection method used to locate surface-breaking defects in all non-porous materials (metals, plastics, or ceramics). The penetrant may be applied to all non-ferrous materials & ferrous materials, although for ferrous components magnetic particle inspection is often used instead for its sub-surface detection capability.

Top Coat Water-Based

Water-based polyurethane is popular because of its low odor & low toxicity. It goes on clear without adding a faint color like oil-based versions do & it dries much faster.